Ok, I glanced at the article and as another engineer, yes it looks sketchy and probably isn’t safe (applying the rule from rigging of: if something doesn’t look right it probably isn’t). I felt the need to address the other issues you brought up about being impossible to calculate because it’s wood. Wood is the original composite material and has been used to safety build bridges, buildings, ships etc. For the most part your calculations won’t be as exact as with metal or other engineered material but there has been lots of research into this. The US Department of Agriculture/ US Forest Service even publish a free book about it. [1] The lumber looks like it was bought from a home center and so likely has minimum strength expectations [6-3 of afore mentioned book].
I just felt the need to dispel this rumor that is quite dangerous that I see all the time at work where people use 1/4 wire rope slings with unrated hardware as part of rigging instead of 1/2 inch Manila rope because “That rope doesn’t have any rating, it’s natural”. (It does, about 1/2 the wire rope, but needs knots or splices to attach it to thing being lifted, not the unrated hardware that comes with the wire-rope.) Like someone posting further down, I’m more immediately concerned that there is no brace to prevent racking or the use of ratchet straps as a lifting device.
> This whole article is a largely pointless exercise in figuring out how strong some random dude’s wood crane is, even though I have no clue what the load case is.
In the US, there is typically a vertical stud every 16 inches, and no lateral braces at all, except for windows and doors, and where dimensional lumber terminates. There's lots of lateral support from ceiling, siding, etc, but the question seemed to imply there aren't many vertical sticks in a wall. Apologies if I misunderstood.
By depth, do you mean cross bracing? Any discussion about lumber strength is beside the point, the fasteners will pull out as soon as it goes sideways.
By depth I meant thickness. But thickness sideways doesn't help nearly as much as thickness in the vertical direction.
A beam with a bending load like here can crack from the bending at the middle for example. The fasteners at the ends are not necessarily the limit. It's different for pure compression or tension, there the fastener area sees higher load.
I totally agree!
Impossible to read with an ad break every paragraph.
In addition, if doing such a long and detailed article, the author could have spent a few minutes to draw on computer clean version of his schematics. Instead of unreadable pictures of hand drawn thing.
Fun article to read. The author started to get into the more likely failure modes at the end when time ran out.
Stability is probably the most important. Next is failure of the wood near the screws, which affects stability. Wood has its own considerations due to the grain. The American Wood Council has a fastener calculator which shows a few of the things that matter when doing structural design with wood.
Every service involving the engine begins with something like:
Step 1: remove headlights and front bumper
Step 2: remove myriad heat exchangers
Step 3: remove engine
So of course you're looking at an Audi Quattro platform getting its engine pulled in a parking space. I wouldn't be surprised one bit if this was all happening just to replace an inaccessible $100 part.
The author also neglected the extras that would needed to be lifted including (usually) the transmission attached to the engine (another 200 lbs right there)
18 comments
[ 2.7 ms ] story [ 43.1 ms ] threadAny math to calculate resultant stress is meaningless, because we have no data on how uniformly dense the wood is.
Not to mention it looks flimsy to the point of being cartoonish.
I just felt the need to dispel this rumor that is quite dangerous that I see all the time at work where people use 1/4 wire rope slings with unrated hardware as part of rigging instead of 1/2 inch Manila rope because “That rope doesn’t have any rating, it’s natural”. (It does, about 1/2 the wire rope, but needs knots or splices to attach it to thing being lifted, not the unrated hardware that comes with the wire-rope.) Like someone posting further down, I’m more immediately concerned that there is no brace to prevent racking or the use of ratchet straps as a lifting device.
[1] https://www.fpl.fs.fed.us/documnts/fplgtr/fplgtr113/fplgtr11...
> This whole article is a largely pointless exercise in figuring out how strong some random dude’s wood crane is, even though I have no clue what the load case is.
What he showed is the crane is plenty strong enough to hold the engine--the failure mode is tipping, not strength.
That's what trees evolved for.
A beam with a bending load like here can crack from the bending at the middle for example. The fasteners at the ends are not necessarily the limit. It's different for pure compression or tension, there the fastener area sees higher load.
Compression load on the vertical members? Who cares.
Strain on the long cross member? Wood fails gracefully and you'd hear cracking.
Forward-backward stability? Probably okay if those joints are screwed really tight and ideally wood glued.
Side-side stability? Good bye!
In addition, if doing such a long and detailed article, the author could have spent a few minutes to draw on computer clean version of his schematics. Instead of unreadable pictures of hand drawn thing.
Stability is probably the most important. Next is failure of the wood near the screws, which affects stability. Wood has its own considerations due to the grain. The American Wood Council has a fastener calculator which shows a few of the things that matter when doing structural design with wood.
http://www.awc.org/calculators/connections/ccstyle.asp
On a positive note, I suspect Americans are a lot more proficient with fractions than people who grew up learning metric.
Every service involving the engine begins with something like:
So of course you're looking at an Audi Quattro platform getting its engine pulled in a parking space. I wouldn't be surprised one bit if this was all happening just to replace an inaccessible $100 part.