> Unfortunately, the laws of physics driving DRAM cells have not improved much over the last couple of years (or decades, for that matter), so memory chips still must operate with similar absolute latencies, driving up the relative CAS latency. In this case 14ns remains the gold standard, with CAS latencies at the new speeds being set to hold absolute latencies around that mark.
Some gaming memory kits can do 10ns or less latency. Though I guess if memory latency is your bottleneck, you should look at HBM.
The smallest transfer done from memory is a single cache line, which on most desktop machines is 64 bytes, or 512 bits. You could imagine a memory bus that was 512 bits wide and transferred a cache line per clock, and this would improve latency when compared to a serial bus with higher clock speed. HBM doesn't do that, though, instead every HBM3 module has 16 individual 64-bit channels, with 8n prefetch (that is, when you send a single request to a single channel, it will respond with 512 bits over 8 cycles).
Just to make sure I understand: you're saying that checking L1/L2/L3 takes around 35ns, and then the CPU accesses DRAM which takes 10ns? If that's so, how is L3 cache any faster than DRAM? Also, can you explain why the memory controller adds some latency?
An L3 hit only takes ~15 ns so that means another 15-20 ns is spent traversing the fabric and memory controller. I'm not sure what all is involved there but for Intel it has to go around the ring and for AMD it has to cross chiplets.
Interesting. If an L3 hit takes 15 ns, then based on your argument a hypothetical CPU with only one core (and hence no fabric) would be better off without L3, since a DRAM read can be performed in just 10 ns.
You still need a memory controller, you still need to get to that controller on the edge of the die. And going to RAM more often will surely consume more power.
This is the part I don't understand. You're saying that the interval from when the DRAM first receives a read request to when it sends the data back over the channel is about 10ns, at least in fancy gaming RAM. Ok, fine. Where is the other 10-20 ns of latency coming from? Why can't the CPU begin using the data as soon as it arrives? I guess some time is needed to move the data from the memory controller to the actual CPU core. But it seems to me (far from an expert) that this shouldn't take a full 10-20 ns. Or am I mistaken?
Firstly, to clarify, there's nothing very special about 'gaming ram' other than the particular chunk of silicon performs better than others so they stuck a shiny sticker and an oversized heatsink on.
The problem here is the latency is state dependent and who knows what people are talking about here. The memory itself can have a latency 1-3x the CAS Latency number and you need to understand how DRAM is accessed to appreciate why. Which will also clarify why an L3 cache is such a good idea.
> For a completely unknown memory access (AKA Random access), the relevant latency is the time to close any open row, plus the time to open the desired row, followed by the CAS latency to read data from it.
Then you've got some small time going to and from the controller, which might also be doing some address translation, maybe some access reordering to avoid switching rows. I think 30ns is very optimistic.
That's CAS latency. To calculate the latency of a timing you divide the timing itself by the clock frequency of your sticks. For example, DDR4-4000 CL14 is running at 2000MHz = 2GHz, so the CAS latency is 14/2 = 7ns.
I'm a bit confused, DDR5 products are already out - as are CPUs and motherboards that support them.
How can this change happen retroactively? Would motherboard manufacturers just need to update the BIOS to enable new XMP configurations? (For when this new, higher transfer rate RAM becomes available)
> while leaving the spec open to further expansions with faster memory as technology progressed
They only set the current standard, but allowed to, if technology progresses, that other speeds/timings would also be jedec compatible, rather than being some kind of XMP. Motherboard manufacturers do not need to upgrade their previous models if the hardware doesn't meet the required SN ratios, or whatever. But they _could_ if they believe they had the hardware to support it.
PRAC should happen automatically in the background when possible and when it really needs to stop the controller from accessing something while waiting for the bits to refresh it uses the already existing ALERTn signal.
> Panopticon retrofits an existing signal in the DDR specification, called ALERTn, to effectively “trick” the memory controller to pause issuing new DDR commands. DRAM uses ALERTn to signal errors to the memory controller. Upon receiving this signal, the memory controller stops issuing new DRAM commands and instead re-issues the old memory access. By making use of ALERTn, Panopticon requires no modifications to any hardware other than DRAM itself.
(As I understand PRAC uses the same design as Panopticon for this part)
It doesn't. If you buy A DDR5-6400 DIMM it doesn't get updated to 8800. It will stay at 6400. This just means that manufacturers will be able to brand their tested DDR5 DIMMs as supporting 8800. You still need a CPU and Mainboard that has been validated at those speeds. You're going to need a 8700G if you actually want to hit those speeds by the way.
I'd like to see the spec tackle latency with a "send then confirm" approach.
Ie. The RAM can reply to a read request with data, then a couple of clock cycles later it can confirm (via a flag) that the data it originally sent was correct.
This is helpful because it means the timing can be tightened to the typical access times, rather than the worst case access time (eg. the slowest preamp on the highest capacitance memory row/column).
Things like CPU's already have provisions for handling not-yet-confirmed information, and can roll back state if delivered info turns out to be wrong.
Yes, it adds complexity to the whole system, but it seems worth it for a -30% change to memory latency.
I wish we could mix 'I don't care about side channels, use them all' with 'I'm paranoid about side channels, plug them all' on the same machine. Disable speculative execution on one core, no frequency adjustment, no prefetching, sr-io/pcie-bypass some devices... E-cores but for the side-channel-paranoid (in a good way).
Bring back EIEIO, like on Old Macs, but perhaps with a slightly expanded definition of what constitutes I/O:
Enforce In-order Execution of I/O (EIEIO) is an assembly language
instruction used on the PowerPC central processing unit (CPU) which
prevents one memory or input/output (I/O) operation from starting until
the previous memory or I/O operation completed. This instruction is needed ]
as I/O controllers on the system bus require that accesses follow a
particular order, while the CPU reorders accesses to optimize memory
bandwidth usage.
I mean permanently disable all speculative execution on a specific core and reduce/disable all side-channels of the kind. If you're saying I can do through injection of fence instructions between every instruction, coupled with isolcpus... I might have a fun weekend coming playing with Intel Pin. But I'm guessing the performance hit might be worse than 'just' disabling speculative execution on a core - if it was possible at all - or that the fence instructions might not be enough there? Haven't thought it through.
But it would be a fun question to ask the likes of Daniel Gruss...
Yes! Having two architectures, one meant to securely run in a “zero trust” environment, and one meant to run at max speed while assuming inputs and code can be trusted (or will never have the opportunity to be executed such as in an airgapped environment) is reasonable. You can even combine the two and we do in practice, as seen with hardware security modules. At a grocery store you will see a lower security cash register with many functions and features connected to a higher security card reader that does a very small number of things.
An essential part of security is scoping. The door to the safe is higher security than the door to the bank. Speed & convenience & cost are paramount at the entrance to the bank, and security is paramount when it comes to securing the cash at the bank. We don’t act as though high security is always warranted when it comes to physical security so why would it be always be warranted when it comes to computer security? Sacrificing speed and convenience is willfully inflicting a denial of service on yourself, it’s only worth it if it’s less bad than the probable alternative.
Every personal computer sold has massive security flaws with only the most severe issues getting papered over and yet most people don’t have issues because the world isn’t actually all that hostile.
How many cycles could this actually save? I would assume the latency to actually get data from DDR is only a small part of the whole round-trip in a L1 miss. Actual savings much smaller than 30%.
From my rough knowledge of textbooks RAM access is usually in the hundreds of cycles. The napkin math makes more sense in that order of magnitude too! In any case it seems unlikely L3 has similar latency considering memory heirachy!
How do you expect that to happen? By sharing memory channels you are no longer using a point to point connection and are now prone to reflections in the PCB traces where you have split the signal. There is no "money" that can be put into this, that won't also improve the performance of the single DIMM per channel setup disproportionately.
I don't even understand what your point is. Quad channel support would be a much better idea since it doubles your memory bandwidth, while remaining a point to point connection, but you're going to complain that you can't add eight DIMMs then.
What if you give each slot independent command pins but not a complete memory channel?
What if you use a similar technology to registered or load-reduced memory, but put the register on the system board instead of the DIMM so it's in front of multiple DIMMs that then share the channel into the processor but not the traces on the system board? This may also allow higher capacity DIMMs in consumer systems.
4 DIMMs on a consumer board means 2 DIMMs per channel. This is inherently a compromise in signal integrity that must come with a speed tradeoff, unfortunately. We’re dealing with laws of physics.
In the past some motherboards tried a T-topology for RAM slots to optimize for 2 DIMMs per channel, but this would cause problems with 1 DIMM per channel usage. Not worth it for the average consumer.
The way to do that would be with a chip & socket that has 4 independent memory channels (threadripper I think has eight now, but maybe used to have four?) and a many-layered motherboard that optimizes the routing and placement of each dimm slot, ideally with only 1 dimm slot per channel for maximum speed. The high end stuff with many memory channels generally isn't designed for pushing RAM clocks to gaming desktop speeds, though. You'd probably need to skip on ECC too or overclock and manually time some.
183 comments
[ 2.0 ms ] story [ 215 ms ] threadSome gaming memory kits can do 10ns or less latency. Though I guess if memory latency is your bottleneck, you should look at HBM.
Parallel means latency if you have non "embarrassingly parallelizable" tasks?
Renesas did have a special Low Latency HBM thing at one point, but I don't think it ever saw the light of day.
Without a thorough analysis by real engineers my interpretation of this statement is "DRAM marketers can print anything they want on the sticker".
Source? My overclocked desktop RAM shows 45ns in benchmarks. I call bullshit on 4.5x faster RAM. Most people fight for an extra 5% latency reduction
The problem here is the latency is state dependent and who knows what people are talking about here. The memory itself can have a latency 1-3x the CAS Latency number and you need to understand how DRAM is accessed to appreciate why. Which will also clarify why an L3 cache is such a good idea.
> For a completely unknown memory access (AKA Random access), the relevant latency is the time to close any open row, plus the time to open the desired row, followed by the CAS latency to read data from it.
(It's actually worse than than for DDR5.)
https://en.m.wikipedia.org/wiki/CAS_latency
https://en.m.wikipedia.org/wiki/Memory_timings
https://www.anandtech.com/show/3851/everything-you-always-wa...
Then you've got some small time going to and from the controller, which might also be doing some address translation, maybe some access reordering to avoid switching rows. I think 30ns is very optimistic.
But it's just a singular timing that's not even used all that often, so it's not that relevant to performance anyway - https://www.youtube.com/watch?v=pgb8N23tsfA
How can this change happen retroactively? Would motherboard manufacturers just need to update the BIOS to enable new XMP configurations? (For when this new, higher transfer rate RAM becomes available)
They only set the current standard, but allowed to, if technology progresses, that other speeds/timings would also be jedec compatible, rather than being some kind of XMP. Motherboard manufacturers do not need to upgrade their previous models if the hardware doesn't meet the required SN ratios, or whatever. But they _could_ if they believe they had the hardware to support it.
PRAC would need handling in the memory controller, so that would require a CPU update if I understand correctly.
https://stefan.t8k2.com/rh/PRAC/index.html
> Panopticon retrofits an existing signal in the DDR specification, called ALERTn, to effectively “trick” the memory controller to pause issuing new DDR commands. DRAM uses ALERTn to signal errors to the memory controller. Upon receiving this signal, the memory controller stops issuing new DRAM commands and instead re-issues the old memory access. By making use of ALERTn, Panopticon requires no modifications to any hardware other than DRAM itself.
(As I understand PRAC uses the same design as Panopticon for this part)
It doesn't mean that any particular combination of CPU/motherboard/RAM will work.
Ie. The RAM can reply to a read request with data, then a couple of clock cycles later it can confirm (via a flag) that the data it originally sent was correct.
This is helpful because it means the timing can be tightened to the typical access times, rather than the worst case access time (eg. the slowest preamp on the highest capacitance memory row/column).
Things like CPU's already have provisions for handling not-yet-confirmed information, and can roll back state if delivered info turns out to be wrong.
Yes, it adds complexity to the whole system, but it seems worth it for a -30% change to memory latency.
But it would be a fun question to ask the likes of Daniel Gruss...
This is what we should reserve Nobel prizes in computer science for
We shouldn’t sacrifice something for nothing.
An essential part of security is scoping. The door to the safe is higher security than the door to the bank. Speed & convenience & cost are paramount at the entrance to the bank, and security is paramount when it comes to securing the cash at the bank. We don’t act as though high security is always warranted when it comes to physical security so why would it be always be warranted when it comes to computer security? Sacrificing speed and convenience is willfully inflicting a denial of service on yourself, it’s only worth it if it’s less bad than the probable alternative.
Every personal computer sold has massive security flaws with only the most severe issues getting papered over and yet most people don’t have issues because the world isn’t actually all that hostile.
E.g., on Skylake an L3 hit is 80 cycles (~20ns) whereas a RAM access is 80 cycles plus 50 nanos (~70 nanos). See https://www.7-cpu.com/cpu/Skylake_X.html
Interesting discussion though!
What if you use a similar technology to registered or load-reduced memory, but put the register on the system board instead of the DIMM so it's in front of multiple DIMMs that then share the channel into the processor but not the traces on the system board? This may also allow higher capacity DIMMs in consumer systems.
In the past some motherboards tried a T-topology for RAM slots to optimize for 2 DIMMs per channel, but this would cause problems with 1 DIMM per channel usage. Not worth it for the average consumer.